![iflash cable iflash cable](https://www.vrtuned.com/images/VRT-ENET-cable-1.jpg)
- #Iflash cable how to
- #Iflash cable install
- #Iflash cable software
- #Iflash cable Pc
- #Iflash cable windows 7
Once you install the program, access your device manager and update the driver or replace it with this one here.
#Iflash cable windows 7
![iflash cable iflash cable](https://images-na.ssl-images-amazon.com/images/I/41ebwmA1RBL._SL500_AC_SS350_.jpg)
![iflash cable iflash cable](http://www.tankya.com/u_file/1703/photo/fdf1d77f5e.jpg)
Because you need to connect the cable from your car to your computer, a Laptop or Tablet is required and should be plugged in while doing the process.
#Iflash cable Pc
This can be any PC and we have heard of Mac’s working if booted up as a Windows machine.
#Iflash cable software
The software is either saved on the included memory stick in your Flash Kit or emailed to you specific for your vehicle. This is program is installed like any program on your computer as a.
#Iflash cable how to
****If you are a previous customer and your software application has expired, please go to the Download Here section and see the notes how to proceed and redownload the latest application.**** If you are using the HP Tuners MPVI2, follow these instructions here. If you are flashing your VW/Audi DSG Transmission, follow these instructions here.įor Polaris ECU Flashing, follow these instructions here.įor Canam ECU Flashing, follow these instructions here. If you have a Alientech Powergate 3 handheld unit, follow these instructions here instead.įor BMW F-Series follow these instructions here. If you have a DimSport MyGenius handheld unit, follow these instructions here instead. If you cannot get it to work on your computer, you may want to try another computer, different version of Windows, or have someone help you configure your PC. We will gladly help to the best of our ability, however we are not Windows technicians nor work for Microsoft. Installation does require you have administrator permissions. You may also have to install the driver separately. If you have errors related to the USB Device, follow the instructions below and try to disable the driver signature. Installing this software is the same as installing any WINDOWS application.
![iflash cable iflash cable](https://i.pinimg.com/originals/6c/2e/4b/6c2e4ba96df29db3aaad34fa295c18ad.jpg)
Once the cable is locked to your VIN, the cable cannot be refunded.*********** This is the responsibility of YOU, the customer. We have NO control over this or a way of knowing if your ECU has been flashed previous to your purchase. We will then fix your ECU to work with the cable and return it back to you. The only way to read out the ECU and fix this issue is in boot mode on the bench. Even if the ECU was flashed back to “stock” by these companies, the ECU still cannot be read. Some companies do things to the ECU processor that will not allow it to be read out via OBDII. ***********Attention!!! If you are NOT the first owner of your vehicle, it is possible that your vehicle could have been flashed previously. ****Also Note – Once you lock your cable to your VIN, our Terms & Conditions apply**** IPod is now ready to restore & sync using iTunes.***PLEASE READ THIS ENTIRE PAGE BEFORE PROCEEDING*** Slide battery cable in to the connector and push down the black latch to lock the ribbon in place. Fold the piece in half for thick case back iPods. Remove the protective outer sheets from the thermal gap filler before placing on top of the mSata drive. Insert the mSata drive fully in to the connector at an angle, then gently push down till it locks on the iFlash-Sata. Install iFlash-Sata board in to iPod, Make sure ribbon is fully home and the black bar is locked down. iPod is ready to accept the iFlash board. Remove all rubber bumpers and strips from the iPods if any remain after the HDD is removed. Gently lift the black bar to release the ribbon from the HDD. Rest the front and back side by side, be careful to not cause too much stress on the headphone ribbon.īefore pulling the case apart, release the battery cable – lift the black lock bar -or- gently using even pressure pull up the battery ribbon away from the connector. I suggest watching some iPod opening videos on the internet. Using suitable tools, release the holding clips, making your way around the case till it opens.